Booster Pump Water Pressure Centrifugal Jet Self Priming Multi Stage Submersible
To find more interesting products. We distribute products from A to Z on the Internet. As we work more cost-effective than the sales in the traditional retail, we can deliver quality products at a good price. Our sales department will be happy to answer your questions.
Contact details can be found in the item description. And the best of all, your goods will be delivered directly to your home. All products in almost unbeatable price-performance. Workshop and Spare parts service. SELECTION 1: Inno Tec 600-5.
Energy saving pump, self-priming with 1.2m rubber cable. SELECTION 2: INNO-TEC 750-5 Pump with 1.2m Rubber Cable. SELECTION 3: Inno-Tec 450-5 Pump. Self-priming, energy efficient and has 1.2m rubber cable. SELECTION 5: Automatic flow switch TEEPRES® (wired) and 2L filter. Intelligent pump control TEEPRES® with leak monitoring and emergency shutdown functions. SELECTION 6: Brio automatic flow switch (wired) and 2L filter. Automatic flow switch Brio (wired). SELECTION 7: Automatic flow switch Fluomac (wired) and 2L filter. Fluomac automatic pump switch (wired) is made in EU. Suction set, floating extraction with hose. Brass screw connection 1 inch internal thread on 1 inch external thread. INNO-TEC 450-5, 600-5 & 750-5 Booster Pumps with Flow Switch and Various Suction Sets. Ideal for boosting pressure of drinking water in a home. Ideal for domestic water and rainwater harvesting use in homes and gardens. Suitable for watering lawns and beds.Can be used for the utilisation of water from creeks, rivers and wells. Self-priming, reliable, four-stage centrifugal pump. Very good quality made in Italy. Professional pump for continuous operation. Extremely quiet despite high flow rate.
Long lifespan due to high quality materials. Suction height upto 7m / 9m. High quality stainless steel housing. A screw connection and a pre-filter is included in the pump control! INNO-TEC PUMP 450-5/ 600-5 / 750-5. INNO-TEC 450-5/ 600-5 / 750-5. Is a very reliable and solid multi-stage centrifugal pump.It is versatile and ideal for use for e. Drinking, domestic and rainwater in a household (no foodstuff certification). It supplies consumers with sufficient pressure. It can also be used in gardens to irrigate lawns or flower beds or for connecting to a lawn sprinkler.
It is ideal for both mobile and stationary use. Commissioning is done by filling the impeller chambers and hose. The rest is done by the pump itself. There is a maximum suction height of upto 9m. A check valve must be installed at the lower end of the suction hose. Please ensure that the suction hose is laid steadily towards the pump. This is important so that the air that may be present in the suction hose can escape to the pump. The careful selection of special materials ensures a long service life of pumps. INNO-TEC 600-5 Pump with 1.2m Rubber Cable.5 bar; flow rate 5200l/h; P2=550W / P1=880W. INNO-TEC 750-5 Pump with 1.2m Rubber Cable. 4.5 bar; flow rate 7800l/h; P2=750W / P1=1250W.
INNO-TEC 450-5 Pump with 1.2 m Rubber Cable. 4 bar; flow rate 5200l/h; P2=450W / P1=700W. Flow Switch with Integrated Dry Running Protection.The automatic flow switch switches on (or off) the connected centrifugal pump depending on the demand for water. It switches on via pressure monitoring and switches off via flow detection. Flow rate reduces and the pump switches off if the consumer is closed.
The special feature of these automatic flow switches is the built in dry running protection function. The flow switch turns off the pump automatically (dry run protection) if there is no water (empty cistern) after switching on the pump.
The selection of the right pump flow switch depends on the intended purpose of the pump. We recommend the use of the intelligent TEEPRES pump flow switch which is equipped with leak detection and emergency shutdown.
Each flow switch is supplied with a 2 litres prefilter (up to 5000L/h; 0.15 mesh size). As a result, problems caused by water pollution are significantly reduced. Each flow switch is supplied with a high quality brass screw connection free of charge. Flow Switch TEEPRES&® - Automatic Controller (wired) and 2L Prefilter. Intelligent TEEPRES&® Pump Flow Switch with leak monitoring and emergency shutdown. Ideal for centrifugal pumps, submersible pressure pumps, deep well pumps, fountain pumps, submersible pumps. Ready to plug in wired as water pressure booster with check valve and pressure gauge.Flow Switch BRIO Automatic Controller (wired) and 2L Pre-Filter. It is particularly price sensitive. We recommend the combination with AC 5. Flow Switch FLUOMAC Automatic Controller (wired) and 2L Pre-Filter. We recommend the use of the AC 10 as a solid and robust standard device.
OUR TIP: We recomend the installation of a filter with a flow rate of at least 5200L/h after the pump. This significantly reduces problems caused by water pollution. This set consists of a stable hose, a floating extraction and a brass check valve. For a long service life of the pump, we recommend the use of a floating extraction as much as possible.
The floating suction is connected to the suction side of the pump. This ensures that no sediments, in the worst case sand, are sucked in thereby causing damage to the impellers of the pump. The supplied check valve prevents the suction line from running dry. The suction basket is attached to a float ball and when properly installed sucks clean rainwater about 10cm below the water surface.The coarse meshed suction basket (approximately 1mm) prevents rapid clogging and premature pump failure. When used in tanks, the floating extraction must be fixed in such a way that it does not touch the bottom of the water vessel or suck up any sediments. Suction Set 2 (without hose).
Suction Set 2 consists of. Suction basket made from stainless steel. Plastic float ball 11.4cm (4 1/2 inches). Brass check valve 2.54cm (1 inch) internal thread.
Suction Set 1 (includes 2m hose). Suction Set 1 consists of. 2m kink resistant opaque suction hose 2.54cm (1 inch). Brass hose nozzle 2.54cm (1 inch) external thread. Suction Set 3 (includes 15m hose).
Suction Set 3 consists of. Plastic float ball 11.4cm (4 1/2 inch). 15m kink resistant opaque suction hose 2.54cm (1 inch). Check valve made of brass 2.54cm (1 inch) internal thread.Suction Set 4 (includes 25m hose). Suction Set 4 consists of.
25m kink resistant opaque suction hose 2.54cm (1 inches). INNO-TEC PUMP 450-5 / 600-5 / 750-5 (Depending on Selection). Automatic Flow Switch (wired) with 2 liter pre-filter & brass screw connection. Flow switch/monitor Teepres® / Brio / Teepres (wired) depending on selection. Includes connection accessories (small parts).
1 x 2 litre pre-filter. Suction Set/Suction & Pressure Hose.Set without hose 2m/ 15m/ 25m suction hose (depending on selection) 2.54cm (1 inch) opaque and kink resistant stainless steel suction basket. Hose nozzle (made from brass) 2.54cm (1 inch) external thread. Power: 600 Watt (P1= 0.6kW).
Includes a power cable and UK plug. Pump motor: Insulation class F. Cable length: 1.2m high quality neoprene (rubber) cable H07RN-F.
Housing material: stainless steel AISI 304. Shaft material: stainless steel 1.4104 gem. Impeller material: GFK-reinforced Noryl GFN2V. Mechanical sealing: ceramic graphite NBR.
Connection pressure side: 2.54cm (1 inch) stainless steel internal thread. Connection suction side: 2.54cm (1 inch) stainless steel internal thread.
Particle size: 0.2mm (no sand). Integrated thermal motor protection switch. Power: 750 Watt (P1= 0.75kW). Number of stages: 4 pcs. Impeller material: GFK- reinforced Noryl GFN2V.
INNO-TEC 450-5 Pump with 1.2m Rubber Cable. Power: 450 Watt (P1= 0.45kW). Including a power cable and UK plug. Number of stages: 3 pcs. Pump motor: insulation class F.
Flow Monitor TEEPRES&® - Automatic-Controller. Voltage: 230 Volt AC at 50Hz.
Shutdown flow rate (Qa): 2l/min. Cable length: ca 1.5m with UK plug. Suction connection: 1 inch external thread (BSP). : 1 inch internal thread (BSP).
Operating pressure: 10 bar (150 PSI). Burst pressure: 40 bar (580 PSI). Operating voltage: 220/240V at 50/60Hz. Start-up pressure: 1 - 3.5 bar (adjustable). Pre-set cut-in pressure: 1.5bar (ideal for most applications).
Connection input via 2.54cm (1 inch) external thread. Connection output via 2.54cm (1 inch) internal thread.
Connection via 2.54cm (1 inch) external thread. Voltage: 110 - 230V at 50/60 Hz. Pre-set cut-in pressure: 1.5 bar (ideal for most applications). High quality rubber cable H07RN-F.
We regularly check the product quality of our suppliers and guarantee the best quality and durability for long enjoyment of our products. For used goods, this is reduced to 12 months. If we provide a further guarantee, this is listed in the item description. For used goods this can be ruled out. Write to us and we will solve the problem together!So you is more helpful and us too! We strive constantly to improve the quality and service. Let us deal fairly with each other!
If in doubt, unpack the goods immediately and check this. You will receive an invoice with VAT. Our Conditions, Cancellation and return rights, can be found on our -site. Or below on the supply side.
E-WASTE, BATTERY LEGISLATION, PACKAGING DISPOSAL. The instructions can be found in our Shop. The item "BOOSTER PUMP WATER PRESSURE CENTRIFUGAL JET SELF PRIMING MULTI STAGE SUBMERSIBLE" is in sale since Friday, October 13, 2017. This item is in the category "Garden & Patio\Ponds & Water Features\Pond & Fountain Pumps". The seller is "amur_shop" and is located in Schwallungen.
This item can be shipped to European Union member countries.de