24V Power Adjustable Brushless DC Water Pump DC55JE-24320A 160W High 32m 2000L/H

24VDC High Lift Cascade Water Pump DC55JE-24320A 160W 32m 2000LPH. Equiped with DRY-RUN Protection Mechanism. For Pressure/ Cooling Systems etc. It is NEW TWO-stage Cascade Pump Product of our series, with high lift value. Pump is equiped with DRY-RUN Protection mechanism in default.

1/2 thread(M20) with external diameter of appr. Max static lift: 32 meters.

Max horizontal flow rate: 2000 LPH (33 L/Min). Typical feature is with quite high lift (output pressure) value, but with relatively low flow rate. Suitable for some micro pressure system.

Parameters, cable length and other specific functions can be specially CUSTOMIZED. Under premise of exact discussion and certain MOQ & lead time.

This is a NEW series initiated by our company. If it is old users, you will know that our older single-stage pump DC50E-24150A model or DC55E-24160A model with power consumption of appr. 80W and lift value of appr. As a comparison, this current Two-stage cascade pump DC55JE-24320A model is obviously more powerful.

Brushless DC motor, also known as EC motor; Magnetic Driven. NO DIRECT AC 100-240V POWER CONNECTION, PROHIBITED. Small size but strong; Low consumption & High Efficiency. Long time continuous working with low noise. Safety - no spark, Explosion - proof; Low noise about 40dB. Submersible, 100% waterproof; Max Working Temperature: 100 degree. Wide range of working voltage; Maintenance - free.

Can be used to pump water, oil, other non-corrosive liquids (special liquids are needed to be pre-tested in advance). Variety Power: DC electric source, Battery or Solar Panel, etc. Soft Start with Low in-rush current, Especially suitable for Solar SYS who can not provide over-high startup impulse current. OEM and ODM are accepted based on MOQ and exact inquiry of customers.

Model: DC55JE-24160A Pump (3Phase Speed adjustable brushless DC designed pump, TWO-stage cascade design). 1/2'' threaded external diameter appr. Rated Current: 6.7 A at 24VDC. Power Consumption: 160W at 24VDC.

Life Span: Support continuous work in. Normal working status, up to 30,000 hrs for nice working environment. Plug: 4-PIN connector (a bit special). Cable Length: about 1.5-2 meters. Water Proof: 100% (note: controlbox part not be placed under water).

1 x All-new Original DC55JE-24320A Micro Brushless DC Water Pump (Two-stage Cascade design). NO power supply is included. If power supply is AC/DC power adapter, output capacity of adapter should be 24VDC, 8A 10A. As we see on pictures, the connector of pump is with 4-PIN connector type, which is a bit special. If it happens that our users find that we cannot conveniently find the matching connector for power connection, then there exists a simple while violent way. In Brief, let's directly cut off the cable's connector and we will find that there are two sub-cables inside. As to polarity, it will be typically RED +, BLACK -, connecting with matching 24V DC power supply.

Pump supports being adjusted through rotating potentiometer knob of pump. Through rotating this knob, pump's. Power and flow can be smoothly and continuously adjusted within range of 0 Max value pump can reach. Pump also supports being adjusted by external 05V Analog signal.

When in need, wield off potentiometer knob. Connection and inject corresponding signals to interface ports. Please pay attention on this, as it will change the pump's original status. As to PWM adjustable version, it will have to be specially customized based on MOQ and lead time. It is NOT offered on item link, but only after detailed talk.

NOT SUPPORTED by models in stock. Regarding corresponding pumps, there are some notes (Not only refering to current pump model listed on this page), As follows.

As micro brushless dc pump, it works via electronic commutation while not brush friction, so there exists no loss caused by brush friction. Pump works with relatively high efficiency.

Pump supports continuous long time work with relatively low noise at normal working environment. Land use or submersible installation (Some extra attention needs to be paid to, as mentioned in the final clause) can be both OK, but it cannot be self-priming, just make sure that fluid can actively flow passing through inlet/outlet because pump works via centrifugal force of high-speed rotation of impeller inside (push/throw fluid out). No long-time dry work without fluid, or it may damage the pump. DC 12V or DC 24V power supply (Depending on rated voltage of pump).

No direct AC power powering or over-voltage powering. Do NOT throw the pump or install it violently, as it could damage the pump body. Do NOT throw the pump directly through the cable, to avoid damage of cable. FIX the pump somewhere at work, to avoid its moving at run, causing little in-flow and dry run, though pump has dry-run protection mechanism designed inside. If it is AC/DC Power adapter, make sure that it can offer sufficient power to pump. For example, if it is 24VDC 100W pump, then AC/DC power adapter must have output capacity of 24VDC, >=6A; if it is 12VDC 80W pump, then AC/DC power adapter must have output capacity of 12VDC, 7A or more. Otherwise, it is less powerful to run the pump. Other pumps will be applied with similar mechanism. Do not directly throw or pick the pump through its cable, since it could damage the cable, especially at connection point between cable and pump body. Control box part (rectangle shape) is NOT recommended to be under water. It's recommended to be placed off water, especially at long term work. If really have to, it is recommended that some firm waterproof tapes can be closely wrapped on the controlbox part before it is placed under water, to streghten its waterproof class. Sure, it is without issue if control box is just placed under water for short time. DRY-RUN PROTECTION feature is now equiped in the pump's design. Pump works at rated voltage: when water flow is gone or in-sufficient, pump will auto access protection mode: run & stop, run & stop... To protect pump's motor part from being physically damaged from long time extensive friction and heat at continuous dry run; when water flow is back to sufficient status, pump will immediately normally run. This can help avoid that pump can be easily dead when it dry runs for long time. - It is the NEW feature! Of course, very long time dry run will still need to be avoided by us as users, since pump won't stop but its running sharply slows in this context. Bulk orders can be accepted.

Products are always full in stock, or can be customized for specific requirement after communication. We will pack your item(s) carefully and safely to avoid any damage during transmit; each package has its own tracking No. All return items must be in original condition, in original boxes, and with all paperwork, parts and accessories; We are not responsible and do not accept any damaged return items. We are always aiming to provide you with nice products and services, as nice as we can.

We are always here, just waiting for you. This item is in the category "Garden & Patio\Ponds & Water Features\Pond & Fountain Pumps".

The seller is "shysky" and is located in this country: CN. This item can be shipped worldwide.

Power Source: Electric
Maximum Flow Rate: 2000 L/h
Working Temperature Range: 0~100 Degrees Celsius
Material: Plastic
Voltage Range: 5-24Vdc (24Vdc rated)
Max load current: 6.7A
Suitable For: Aquarium, Fountain & Water Feature Pumps, Koi Ponds, Ponds
Colour: Black
Brand: ZKSJ
Type: Fountain Pump
Unit Type: Unit
Item Height: 112mm
Water Type: Brackish, Fresh, Marine, Pond
Model: DC55JE-24320A
Speed Adjustable: YES
Style: 32m
Features: Submersible
Demension of inlet and outlet: 20mm / 20mm (1/2 inch thread)
Country/Region of Manufacture: China
Power Consumption: 160W at 24VDC
Power: 86.4W
Item Width: 77mm
Item Weight: about 1500g